On many bags and small leather goods, the closure has to do two jobs at once. It must hold the flap or lid, and it must not add an obvious step, bulge or stacked thickness at the set point. That is a profile problem as much as a holding-force problem. A thicker snap body can lift the leather, show a ring through a fine covering, or make two panels sit awkwardly where a slim closure was specified.

Extra-thin magnetic snaps are the published low-profile option for that situation. The live product page describes them as extra thin as well as strong enough to sit flush with the material. The magnet body is set into the thickness of the leather, leaving a thin outer flange to lie flush with the bag’s surface. This article stays with that bag and leather-goods question — stack height and protrusion — rather than a general comparison of thin and thick journal closures.

Extra-thin round magnetic snaps for bags, purses and leather goods

What “extra thin” refers to on the published page

The product page states that thickness is 2 mm. Diameters are listed as 10 mm, 12 mm, 14 mm and 18 mm, with an 8 mm size that can be customised, and a 20 mm option in another structure. Those are the sizes shown for this family. They should not be presented as the complete size range for every Richarms magnetic snap.

The same page lists model codes RC-E1020, RC-E1220, RC-E1420 and RC-E1820, with prong lengths and magnet sizes for each displayed configuration. Because those component figures belong to the listed models, they should be read from the current product table and confirmed against the approved sample. They are not a licence to mix a diameter from one model with a prong length from another.

A further construction point matters for profile. The female part typically contains the magnet, while the male part contains a ferromagnetic material, such as iron or steel, that is attracted to the magnet. That is different from a double-sided snap, in which both sides contain magnets. If a design needs a low-profile set and a one-magnet pairing, the extra-thin construction is the option to evaluate. If the bag must close from either face, a different construction may be required.

Why stack height and protrusion should be checked together

A 2 mm body can still protrude if the set point is not prepared for it. If the leather or covering is not recessed, or if the flange cannot lie flat, the snap will stand proud even though the body is thin. If the recess is too deep, or the surrounding material is very soft, the face may sink and leave a depression. The published description — that the magnet body is set into the thickness of the leather, with a thin outer flange lying flush — is the result to aim for on the sample, not an automatic outcome of choosing the product.

The finished stack still has to be measured. Lining, reinforcement and any hidden carrier add height around the set point. A low-profile snap does not remove the need to match prong, stem or rivet length to that stack. The product page states that sizes in this family can be provided with legs, stems or rivets. The fixing must be trialled on the actual materials. A short outer panel is not a complete specification.

Typical bag and leather-goods uses listed on the page include leather purses, totes, handbags, journal covers, backpacks and shopping bags, together with smaller items such as mini wallets and eyeglass cases. Those examples are starting points. The right diameter still depends on the product structure, the available set area and the required holding force.

Materials, finish and strength without over-specifying

Female capsule materials published for this product include iron, common brass or environmental brass. The male capsule is listed as iron. Finish types include plain, pattern or logo on the female snap, and plain, wording or logo on the male snap. Additional colour options, such as spray black, epoxy black, rainbow, pearl nickel, pearl gold, brush nickel, brush gold, antique silver and antique black, can be discussed from the product page.

The page also discusses hanging plating and roll plating as different electroplating methods. That is a finish-process choice, not a performance rating, and it should be agreed against a visual standard on the approved sample.

Holding-force figures appear on the product page in more than one context, including a general standard range and examples that refer to thicker snaps. This article does not repeat those figures as a specification for the extra-thin family. The useful published principle is simpler: the power of a magnetic snap is determined by the size and strength of the magnet, and the selection should suit the bag. A stronger closure is not automatically better on a fine or lightly supported panel. Confirm the opening feel on the finished article.

A sample checklist for low-profile bag work

  1. State the article and the reason a low profile is required: a flush flap, a slim wallet, a tight lid gap, or a covering that would show a thicker body.
  2. Record the finished stack height at the set point, including leather or fabric, reinforcement and lining.
  3. Decide how the 2 mm body will sit in that stack: recessed into the material, or with the flange on the surface, and what the visible protrusion must not exceed.
  4. Shortlist a listed diameter from the current product table, without treating that list as a complete range for all snaps.
  5. Confirm the fixing (prong, stem or rivet) against the stack, not only against the outer panel.
  6. Approve capsule material, finish and any logo from a production-intent sample, including the plating method if that affects the visible colour.
  7. Check that the flange lies flush and that the covering does not bridge, sink or shine over the set point.
  8. Inspect fixing reliability and magnetic closure force as separate checks.
  9. If the bag must close in more than one orientation, confirm that a one-magnet pairing is still appropriate.

Where to place this option in a bag programme

Extra-thin snaps are one family within the wider offer described on the magnetic snaps resource hub. Use the hub to compare fixing styles, custom options and sourcing questions, then specify the extra-thin models only where stack height and protrusion are genuine design constraints. Final dimensions, materials, finishes and installation methods should be confirmed through an approved sample before mass production.

Richarms is a magnetic snaps manufacturer and custom bag hardware factory founded in Foshan, China, in 2003.

author avatar
ライハース